XFS-7110-2HG
2 x 100G QSFP28 + 4 x 25G SFP28 +
4 x 10G SFP+ L3 Lite Managed Switch
The CTS XFS-7110-2HG provides 680 Gbps switching capacity with 100G, 25G and 10G fiber connectivity for enterprise and data center networks. QSFP28 breakout, dedicated OOB management and IEEE 1588v2 PTP Transparent Clock support flexible deployment and precise time synchronization.
Environmental Condition Operation: 0˚C ~ 50˚C
Storage: -10˚C ~ 60˚C
Humidity:5% ~ 90% RH, Non-condensing
Dimension Size:210 x 290 x 44 mm (W x D x H)
Weight: 2.2 kg
Features
The XFS-7110-2HG combines 100G, 25G and 10G fiber connectivity with VLAN, QoS, STP/RSTP, link aggregation and IGMP/MLD snooping. Dedicated OOB management, intelligent diagnostics and IEEE 1588v2 PTP Transparent Clock support network operation and precise time synchronization.
100G
Delivering 100G ultra-high-speed data transmission to meet the increasing demand for bandwidth-intensive applications, providing exceptional connectivity and scalability for high-performance networks.
25G
Delivering 25G high-speed data transmission to meet the growing demand for bandwidth, enabling faster and more efficient network connectivity for modern enterprise and data center applications.
10G
Equipped with 10G data transmission capacity designed to fulfill the ever-increasing demand for higher bandwidth which is essential for traditional Internet service and premium service alike.
IEEE 1588v2 PTP
Supports IEEE 1588v2 Precision Time Protocol (PTP) Transparent Clock (TC) to improve time synchronization accuracy by compensating for packet residence time within the switch.
Power Down Trap
Notify NOC when power is shut off, thus saving the cost of deploying human resources for troubleshooting.
Power Redundancy
Transition to the other redundant power module if either of the power sources is down.
Flexible IPTV Deployment
Designed with rich functions in facilitating multimedia streaming and providing a stable IPTV service with high quality.
IPv4/IPv6 Dual Stack
Able to run IPv4 and IPv6 in parallel and be interoperable with other IPv4 / IPv6 / dual-stacked devices, which enables IPv6 management, IPv6 packet forwarding, and MLD v1/v2 Snooping.
Multicast VLAN Registration
Reduce the bandwidth required to distribute IPTV multicast streams by means of sharing single traffic across different VLANs.
Smart Fan
Smart Fans adjust fan speed based on temperature to control power usage and reduce noise, instead of just dissipating heat
Dual Image
Safeguard against permanent system crash from firmware upgrade failures.
Hardware Overview
*Rear view shown: XFS-7110-2HG-1AE. Power inputs vary by model.
Specification
Interface
- 2 x 100G QSFP28
(each supports breakout to 4 x 25G) - 4 x 25GBase-R SFP28
- 4 x 10GBase-X SFP+
Console Port
- 1 x RS-232 RJ-45 Serial Port
OOB MGMT Port
- 1 x 10/100/1000BASE-T RJ-45
USB
- 1 x USB 2.0 (Type-A)
LED
- Power, Status, COM, MGMT, USB, Link/Act/Speed
Environmental Condition
- Operation: 0°C ~ 50°C
- Storage: -10°C ~ 60°C
- Humidity: 5% ~ 90% RH, Non-condensing
Power Requirement
- AC Input: 100~240 VAC, 50/60 Hz
- DC Input: 48 VDC
- External DC: 12 VDC (R7B adapter)
Power Consumption (full load)
- At 50°C (Smart Fan): 55 W (187.6 BTU/h)
- At 25°C (Smart Fan): 45 W (153.5 BTU/h)
Hardware
- MAC Address Table: 32K
- Switching Fabric: 680 Gbps
- Forwarding Rate: up to 600 Mpps
- Packet Buffer: 6 MB
- Jumbo Frame: 10 KB
- Store and Forward / Cut-Through
Dimension & Weight
- Size: 210 x 290 x 44 mm (W x D x H)
- Weight: 2.2 kg
Standards & Certifications
- Safety: EN/IEC 62368-1
- EMC: EN 55032 / EN 55035
VCCI/UKCA/RCM
RoHS 2.0
Topology
Application Diagram
Model
Model | Fiber Port | Support Power Source | ||
Speed (bps) | Type | Slots | ||
XFS-7110-2HG-1A | 100G | QSFP28 | 2 | 1 x Fixed Internal 100-240 VAC |
25G | SFP28 | 4 | ||
10G | SFP+ | 4 | ||
XFS-7110-2HG-1D | 100G | QSFP28 | 2 | 1 x Fixed Internal 48 VDC |
25G | SFP28 | 4 | ||
10G | SFP+ | 4 | ||
XFS-7110-2HG-1AE | 100G | QSFP28 | 2 | 1 x Fixed Internal 100-240 VAC + 1 x Fixed External 12 VDC (via R7B adapter) |
25G | SFP28 | 4 | ||
10G | SFP+ | 4 | ||
Each 100G QSFP28 port supports breakout to 4 x 25G interfaces.
Download
*To update the firmware, unzip the .zip file and upload the *.bin file.
*To use *.mib file for SNMP service, unzip the .zip file.
